Create a foot of flame in one of the most unlikely places possible -- a pool of water! By combining a unique underwater manifold and a high-tech valve system, this product produces a full, one foot diameter circle of flame from the shimmering surface of your reflecting pool, the top of a fountain, or even just a bowl of water.
This new version has a few new extras. It's engineered so that water won't flood the gas line. It has a check valve built-in that prevents liquid from getting into the pipe, only opening when the gas is turned on and the pressure can keep the line clear. The revamped design allows the jets to be mounted nearer the water surface to use less PSI of pressure than older fire-on-water modules.
Easy startup thanks to the electronic ignition system that controls the flow of fuel to the components. Connect it to the fuel line and a 24 volt AC power source (like a pool timer, or a 110~120 volt AC home source with a 24 volt transformer, not included), and as soon as it gets power it will turn on the gas and light it automatically. Even if the wind blows it out, the on-board sensor will detect the flame and try to light it again. If the gas is turned off or the power goes out, the system will power down until it has access to both fuel sources.
There are two types of electronic ignition for you to choose from: A SUBmersible Electronic Ignition System (SUBEIS) that mounts right to the manifold and sets in the water, and an Automated Fire On Water (AFOW) ignition that sets outside of the feature up to twenty feet (20') away for easier access and maintenance.
It uses your choice of natural gas or liquid propane fuel.
Benefits and features:
Proudly made in the USA
Once the electronic ignition system is turned on (SUBEIS shown), the gas will flow through the manifold, out of the water, and into the air.
After a few moments, the pilot light will turn on, igniting the gas that is escaping over the water.
The result is that the flame will hover over the water, stopping at the waterline, keeping the manifold and electronics protected from the heat.
There are two different ignition systems that you can choose to start the gas on your submersible manifold. While the two systems operate identically for the most part, they install quite differently.
The SUBmersible Electronic Ignition System (SUBEIS) has a sealed electronic valve system that is designed to be submerged in the water. The manifold attaches directly to the SUBEIS.
The Automated Fire On Water (AFOW) ignition system is not sealed and must be installed outside of the water feature. The pilot igniter's wire and gas line can be ordered up to 20 feet long.
It's recommended that you install it 1/2" to 2" below the surface of the water. The closer you install the manifold to the surface of the water, the better the performance you will get.
Do not run manifold without it being submersed in water! The heat could damage the check valve and electronics.
These products require minimum 0.5 psi to operate. If you install the manifold deeper than recommended you may need a higher pressure line. You will need to get a high pressure regulator installed to the fire feature with a pressure regulated spring rated at 3 - 6 PSI. For natural gas installation you require a high output meter, usually supplied by your gas provider at no cost to you. For propane installation you will need a high output regulator, usually supplied by your gas provider. It has to be rated for at least 3 PSI and up.
All manifolds are shipped with a check valve that prevents backwash.
The manifold is made out of 316 stainless steel, and is rated to resist saltwater and corrosion.
These features require the use an AFOW or SUBEIS electronic ignition to light. These systems act as both the gas valve and the ignition, and are perfect for manifolds that are mounted in the middle of large bodies of water. ALWAYS STAND UPWIND WHEN LIGHTING ANY FIRE FEATURE!
It is the buyer's responsibility to check local codes, restrictions and enforcement for installations. Units must be installed by a local licensed contractor. CAN NOT BE USED INDOORS!
NO. The parts are configured, sealed and powder coated in a specific configuration to meet safety standards, but there's good news: Larger sizes and different shapes are available for custom order. Please contact our office at 1-888-986-1535 if you need something special.
There is a one year warranty on the stainless steel material. The replacement tips have a 3 month warranty and can be ordered at any time. With proper maintenance, the tips should last for up to 2 years, depending on the hardness of the water. The system is very durable and is built to last.
Usually ships in 5-10 Business Days.
Due to the custom nature of this product, it is not returnable.
|Material||#316 Stainless Steel (manifold)|
|Fuel Type||Natural gas or liquid propane|
|Required Pressure||0.5 PSI|
|Voltage||24 volts AC|
Our loyal customers have left 56 company testimonials giving us an average of 5/5 stars for great service. Would you like to leave your own feedback, testimonial, or review? Leave My Feedback
Thank you for responding and extending a discount offer to me. I'm so very impressed by your concern for just one customer, thanks. Also thank you for the advice about what may happen if we shut the doors completely.
Wow, fast turn around on my order.
I was concerned that the glass wouldnt be real ceramic, but it is. it only took them 3 days to get it cut and delivered. it took 2 weeks when i ordered from woodland last year. much better job at cjs. thanks
I really enjoyed working with you! Your attention to detail and follow up were beyond expectation.
Coal Stove Glass
Glass arrived in 4 days in a well packed box. I believe i could of thrown the box out a window without cracking the glass . Product was exactly as ordered with nice smooth edges. Than k you guys