8 Inch Ventis Pipe 316L

8" Double Wall 304L Ventis Inner Wall Pipe Section 18" long. Applications for standard solid fuels Product Specifications: 6" Inner Diameter Inner Wall is .016" thick and mode from 304L Stainless Steel Outer Wall is .016" thick and made from 430...

8" Double Wall 316L Ventis Chimney Pipe End Caps Section This component is required if you are installing Ventis Class-A behind a stone slate or other bespoke shroud. The Pipe End Cap seals the top piece of the pipe, preventing moisture from...

8" Stainless Steel Ventis Square Storm Collar Section A square ceiling support is also employed as an attic insulation shield. The Square Ceiling Support comes with a two-piece trim collar that can be adjusted to fit any ceiling pitch. The faceplate is...

8" Class-A Ventis 30 Degree Wall Pass-Thru Section. When a Class-A chimney goes horizontally through a flammable wall, use the Wall Pass-Thru. The 30° Wall Pass-Thru is perfect for wall penetrations that are below grade! Product...

8" Double Wall 316L Ventis Wide Open Rain Cap Section. The conventional cap allows for more open screening. A nice option for some insect prevention with minimal creosote buildup. Quick-connect clamp for quick cleaning or inspection of the...

7" Ventis Square Ceiling Support Section 24" Tall Extension. The Class A pipe runs through the box. The package includes a pipe clamp. This box is utilized when there is a clearance issue and a single or double wall pipe cannot be used as a connecting...

8" Ventis Galvalume Wall Pass-Thru Section 12" Length Extension. When a Class-A chimney goes horizontally through a flammable wall, use the Wall Pass-Thru. adjustable from 4′′ to 8′′ in length, with a 10′′ finishing...

8" Ventis Galvalume Wall Pass-Thru Section Thimble Non-Insulated Use this when a Class-A chimney passes horizontally through a combustible wall. adjustable from 4" to 8". (You can choose an option with a 12" extension, if needed.) Includes a 10" length...

8" Double Wall 316L Ventis Woodstyle Rain Cap Section. The conventional cap allows for more open screening. A nice option for some insect prevention with minimal creosote buildup. A quick-connect clamp for quick cleaning or inspection of the...

8" Ventis Square Ceiling Support Section 24" Tall. Ceiling supports, both square and round, can be utilized on flat, cathedral, or inclined ceilings. Both versions are 11" tall and contain a trim collar and clamp. A firestop is required when going...

8" Ventis 430 Wall Pass-Thru Cover Plate Section. The conventional cap allows for more open screening. A nice option for some insect prevention with minimal creosote buildup. Quick-connect clamp for quick cleaning or inspection of the chimney. Product...

8" Double Wall 316L Ventis Standard Rain Cap Section. The conventional cap allows for more open screening. A nice option for some insect prevention with minimal creosote buildup. A quick-connect clamp for quick cleaning or inspection of the...

8" Ventis Square Ceiling Support Section 11" Tall. Ceiling supports, both square and round, can be utilized on flat, cathedral, or inclined ceilings. Both versions are 11" tall and contain a trim collar and clamp. A firestop is required when going...

8" Ventis 430 Wall Pass-Thru Siding Trim Kit Section. When the structure has aluminum or vinyl siding, it is used to seal the outside of the wall pass-through. The Siding Trim Kit must be used in conjunction with the Wall Pass-Thru. The Fresh Air Intake...

316L Ventis Short Body Insulated Tee With Tee Cap Section 8" Diameter. This tee can be installed at the base of the chimney, either on the interior or the exterior of the structure. The tee features a deep bottom reservoir, which means you...

8" Galvalume Ventis Non-Vented Metal Roof Flashing 7/12 to 12/12 Pitch. Trace the front edge of the metal roof profile and cut for a precise fit. Product Specifications: Unique design that solves the challenges of Metal Roof...

8" Ventis Sloped Ceiling Trim Collar Section for Class-A Pipe. When installing a Round Ceiling Support, a 36" Finishing cover over Class-A pipe on a roof-supported installation, or exposed Class-A pipe on a roof supported installation, this product...

316L Ventis Insulated Tee Cap Section 8" Diameter. The tee cover is located at the base of the chimney. The tee cover is now easier to remove thanks to a one-nut driver connection; it's easy to remove while being childproof. Install the tee...

8" Galvalume Ventis Non-Vented Metal Roof Flashing 0/12 to 6/12 Pitch. Trace the metal roof profile on the front edge of the flashing and cut for a precise fit. The Integral Snow Wedge on the high side of the Flashing Divers slides snow, ice, and...

8" Ventis Sloped Ceiling Trim Collar Section for Finishing Cover, when installing a round ceiling support. This product is used on sloping ceilings where there is (2) a 36" finishing cover over Class-A pipe on a roof-supported installation, or (3)...

316L Ventis Insulated Tee With Tee Cap Section 8" Diameter. This tee can be put on the interior or outside of a structure and is located at the base of the chimney. The accompanying tee cover is now easier to remove thanks to a one-nut driver...

8" Double Wall Galvalume Ventis ​​​​​​Vented Peak Flashing. Use when coming through the peak of the roof. No matter what the peak is, this Flashing will work for you. Product Specifications: Use when passing through the peak of the roof Will work no...

8" Ventis Sloped Ceiling Trim Collar Section for Round Ceiling Support Box. Ceiling supports, both square and round, can be utilized on flat, cathedral, or inclined ceilings. Square and Round Support Boxes are each 11" tall and come with a trim...

8" Double Wall 316L Ventis Chimney Pipe Elbow Section 30 Degree. The kit comprises two elbows and one elbow support. available in 15 and 30 degree angles. It also offsets impediments like building joists. In a single installation, no more than four...